Athletes need to warm up before the game, cars need to warm up before driving, people and cars have commonalities. According to the engine coolant temperature can be divided into two states, below 70 °C belong to cold cars, above 70 °C after the hot car. There are two common cold car breakdowns: cold car idle jitter and cold car acceleration, many drivers friends know what to do with these faults, the following one by one to make an analysis.

Cold crank shake

If cold idle jitter and hot vehicle idle jitter exist at the same time, first eliminate the hot vehicle idle jitter fault. Defining whether to belong to the jitter should observe whether the pointer of the engine tachometer swings or reads the engine speed in the data block, because the engine foot pad damage also causes the engine idle jitter, especially when the automatic vehicle is engaged in the forward gear.

The causes of cold idle vibration are:

1, the engine mechanical failure. For example, the pressure of each cylinder is not uniform;

2, the intake system failure, such as air intake pipe leakage. Excessive carbon deposition in the intake valve and intake pipe, too much dirt on the throttle and intake pipe inner wall, etc.;

3, engine management system failure. For example, water temperature, intake air temperature signal is incorrect, line faults, etc.;

4, there is a fault in the ignition system. For example, there are too many carbon deposits in the spark plugs or gaps, leakage of high-voltage lines, distributor caps, and damage to the ignition coils;

5, oil supply system failure. For example, the injection of oil due to excessive coal deposits inside the nozzle caused the nozzle is not closed or blocked.

Bad cold acceleration

Although many car manufacturers' user manuals indicate that the cold car can be started without preheating after start-up, I believe that it is beneficial to preheat the engine slightly after warming up for 3-5 minutes because it can reduce the mechanical wear of the engine and reduce the displacement of the engine. The car can make enough engine power at the start. The cold start and the start of the accelerator are the wrong driving methods. At this time, the acceleration car that appears will be avoided. If the cold car starts slowly, it will be a fault.

Reasons for poor acceleration of cold vehicles include:

1, the engine mechanical fault. For example, a low cylinder pressure results in a decrease in engine power, a more prominent condition in a cold vehicle, and an excessive amount of carbon in intake valves and intake pipes;

2, intake valve and intake pipe excessive carbon deposition. Causes the injected gasoline to be adsorbed by coke and cannot enter the combustion chamber;

3, engine management system failure. For example, water temperature, intake air temperature signal is incorrect, line faults, etc.;

4, there is a fault in the ignition system. For example, there are too many carbon deposits in the spark plugs or gaps, leakage of high-voltage lines, distributor caps, and damage to the ignition coils;

5, oil supply system failure. For example, the injection of oil due to excessive coal deposits inside the nozzle caused the nozzle is not closed or blocked.


The rare-earth metal thick film heating technology is one of today's most innovation and forward-looking solution for electric heating field.The thick film heating tubes/elements are produced by screen-printing dielectrics (5 layers), resistance (palladium-silver), conductor (silver) and isolation glazes on the substrate and sintered 7-9 times at temperature over 900℃.

Thick Film explosion diagram

 

With 3000W Thick Film Heating Tube simple tubular structure, it can heat water flow inside the tube. Electric Circuit printed on tube surface, to heat the water flow inside. For applications where space is limited, this simple profile heater offers high thermal power density and fast response times to heat up or cool down (due to low thermal mass)


3000w thick film heating tube

 


JIEDA company can supply products according to customers' drawings and offer our clients reasonable prices. Our company also can develop heating solutions and products together with customers.


Those new types Thick Film Heater Tubes are special designed for Through-Flow applications, such as Instant Hot Water dispensers, instant water heaters, instant coffee maker, electric heating water faucet, water purifier instant water flow heater under sink, industrial water flow heater. Maximum heating power: up to 6kw on single tube.


Application of thick film heater

3KW Thick Film Heating Tubes

3000W Thick Film Heating Tubes,Tube Heaters For Sale ,Gas Tube Heater ,Infrared Garage Heater

XINXIANG JIEDA PRECISION ELECTRONICS CO.,LTD , http://www.gidaheater.com

Posted on