1, high-speed tire burst This is a big problem. According to official data, Kazakhstan shows that 70% of highway traffic accidents in China are caused by punctures. It is very dangerous that the vehicle runs at high speed and the puncture or parts fall off. There are two kinds of punctures, one is a front tire, and the other is a rear tire. In either case, the driver can't panic, he can't hurry to hit the steering wheel, and he can't even slam on the brakes. This can easily cause the vehicle to roll over or roll over. Coping methods: Hold the steering wheel firmly with both hands, close the throttle, and turn on the double flash warning light. Wait until the speed drops below 50km/h and then drive the vehicle to the emergency parking zone. During deceleration, you can hang neutral or step down, release the accelerator pedal and lightly apply the brakes repeatedly. 2, steering out of control What is the loss of control? Steering uncontrollable, popularly speaking, is that the steering wheel is no longer in use, hit the steering wheel, but the front wheel does not move, is not controlled by the steering wheel, or the direction becomes very heavy, difficult to turn, the vehicle does not move in the direction that you want. This condition can be caused when components in the steering mechanism are detached, damaged, stuck, or the steering wheel comes off. solution: Immediately loosen the accelerator pedal and hang it to the low speed gear. Evenly and firmly tighten the hand brake. When the speed is obviously decreased, step on the foot brake to stop the vehicle gradually. 3, vehicle sliding The car is skating, it is drifting, like to play with the drift budding sister's buddy, this feeling is naturally so cool, a careless, sister put the body upside down it! However, in the course of daily driving, the harm is enormous. There are generally three situations where a vehicle skids: One is excessive braking before entering the bend and higher side speed causing side slip; The second is that the emergency brake generates a side slip; The third is high speed, steering swiftness caused by sliding. solution: 1. If there is excessive braking before entry into the curve, and if the vehicle speed is high and the steering is relatively late and it is eager to make a side-slip caused by the direction correction, the brake pedal shall be released and the direction reversed to make the drive wheel resume traction; 2. If the emergency brake generates a side slip, stop the brake immediately and play the steering wheel in the direction of the rear wheel's sideslip. However, the speed and the amplitude of the steering wheel must be moderate. 3. If the vehicle speed is high and the side skid caused by sudden steering changes, the throttle should be released to reduce the vehicle speed. At the same time, according to the vehicle speed and the state of side skidding, the steering wheel should be tapped to the side where the side skidding occurs. 4, brake failure When the brakes fail, obviously the brake pedal is stepped on. Many drivers feel that the speed is accelerating or the brake pedal cannot be stepped on. Therefore, they will be very confused. Some drivers with poor mental quality even step on the throttle, which is even more a cup. Don't panic when you are in trouble, there is still overhead on the pressure! Coping methods: Release the throttle, look straight ahead, and control the direction to avoid bumping into other vehicles or buildings. There is no response to the brake pedal. The brake oil may leak or the brake link may break. At this time, the low gear may be hung, the engine brake may be utilized, and the handbrake may be reasonably used. If the brake pedal cannot be stepped on, there may be foreign objects below the pedal. Remove foreign objects while ensuring safety, and do not visit the foreign object to remove the vehicle. 5, tank boiling Have you ever encountered the situation where the car was driving suddenly and the white smoke came from the engine? This is the casserole! To be honest, the boiling water in the tank is boiled. If the temperature of the engine is too high, the expansion of the parts will reduce the clearance for each part to cooperate, so that the viscosity of the oil will be reduced, and the wear of various parts will be aggravated, resulting in a decrease in the life of the engine. Coping methods: Do not immediately turn off the flames, you should quickly find a cool place to stop cooling, let the engine idle, and open the hood to speed up the heat. When adding water, wait until the water temperature drops and it is no longer boiling. Use a wet towel to cover the radiator. First, unscrew the radiator and cover it with water to release the water vapor. Wait a moment and then fully open it. At this time, be careful not to be steamed. Hot to the face and hands. 6. No progress Some underpowered vehicles are susceptible to vehicle retreat if they are climbing a hill, or if the road is slippery, although the power is well-established. Once the vehicle is back, the speed will be faster and faster, and it will eventually be difficult to control. The consequences are quite serious. Coping methods: If you can't go up, don't struggle! Decisively hung upside down, using the engine to control the speed, looking for parking opportunities. 7, emerging obstacles Some overloaded trucks or tricycles often drop some cargo from the vehicle, posing a security threat to the rear vehicles. The driver of the rear car is easily distracted. Coping methods: Concentrate on driving while driving and observe the condition of the road at any time. If you find it is too late, do not rush to the steering wheel at this time, you must step on the brakes, open the double jump lights, to avoid rear-end collision. 8, the vehicle spontaneous combustion Summer temperatures are high, which can easily cause the vehicle's cooling system to malfunction, etc. In addition, some rubber parts are prone to aging, the pressure in the sealed liquid storage container is increased, and automobile oil and other liquids are leaked. If the doors and windows of the vehicle are closed and the exposure time is too long in the summer sun, the maximum temperature in the vehicle can reach 50°C-70°C. At this time, the lighters in the car or the sprays contained in the pressure vessels are likely to be Deflagration occurs due to high temperatures, causing the car to burn. Coping methods: If you smell odors while driving, or you see unclear smoke in your car, you should stop at the curb, pull the handbrake, turn off the power, leave the burning car quickly, and remove the fire extinguisher to cool the fuel tank and the burning parts. Fire and call 119 for help. 9, crash moment In the process of driving, sometimes you are not careful enough to avoid accidents. Your car is driving well, but it may be so unlucky to be implicated by other vehicles. It is time to test a person's ability to respond. Of course, it is absolutely useful to reserve some coping skills in peacetime. Coping methods: In the moment of a collision, you should protect your chest with your arms and hold your head with your hands. The driver should keep away from the steering wheel as much as possible because the steering wheel may hit your chest at high speed and cause harm to you. The rear passengers should lie back and avoid the backrest in the front row. 10, the vehicle fell into the water It is also a time when the rainy season is plentiful. It often rains. In the summer, there are frequent thunderstorms, or nighttime roads, navigation pits, and it is easy for vehicles to fall into the water. In recent years, news of people drowning in vehicles caused by vehicles falling into the water has become commonplace. Coping methods: Open the door as soon as possible. If you cannot open the door, you will smash the window and use a hammer or sharp object to hit the corner of the window to escape. If the doors and windows cannot be opened, the trunk can be used to escape. The steps are: bring down the rear seats → climb into the trunk on the back → find the escape button and press the button. However, not all cars can escape from the trunk. For example, many cars can't fall down on the back seat backrest, but knowing more than one method is always better than not knowing. YT-80 turning machines focus on large enterprises and export customers. Its technology is from Japan. It is automatic line, incorporated with most updated electrical, hydraulic and pneumatic technologies, particularly for high-accuracy, high-productivity and high-reliability turning bearings.Machines can be divided into Outer ring bearing ring machine and Inner ring bearing ring machine.
Automatic Bearing Ring Lathe Machine is a special equipment for turning inner and outer rings of small and medium-sized rolling bearings. The main processing objects are 628-6213 and other models. The assembly line is composed of several single function main machines and various auxiliary machines, which are connected through the slideway to complete the processing of the inner and outer rings of the bearing. It is suitable for the mass production of the inner and outer rings of the rolling bearings. The main engine undertakes the following tasks: inner hole, groove of end face, chamfering of inner and outer rings, separation of inner and outer rings, middle groove and side groove of inner and outer rings. The auxiliary equipment consists of disc feeder, elevator (floor type and bed type), scrap iron crusher, etc. The assembly line integrates mechanical and electrical, pneumatic, hydraulic in one, automatic feeding, processing and cutting, with high degree of automation and short processing cycle. It can flexibly form automatic or semi-automatic assembly lines with different forms and different lengths according to different raw materials and different process requirements of users. The machining accuracy is 0.01mm and the processing technology reaches the domestic advanced level.The machine can choose for double slide turning machine and single slide turning machine.
More than 100 pcs of YUTAI Turning Machines are running in India which supplies best quality products to world class bearing manufacturer SKF, FAG, NSK, NBC etc. Turning Machine,Cnc Turning Lathe,Cnc Turning Lathe Production Line,Cnc Turning Lathe Shaoxing Sunfong Intelligent Equipment Inc. , https://www.zjsxsunfong.com