EVA Traction Pad is the tail pad to be sticked on the surfboard. It comes with center arch and kick tail, which allow surfers to control the direction and stability when surfing in the sea. Eva Traction Pad,Non-Skip Traction Pad,Traction Pad,Surfboard Tail Pads,Grip Tail Pad,Eva Tail Pad Huizhou City Melors Plastic Products Co., Limited , https://www.melorsmarine.com
The design of surfboard traction pad can be in one piece, two pieces, or three pieces basically. The standard the classical texture for traction pad would be diamond like texture, as it can provide the stronger grip among all of them.
The EVA color connect logo is made along with the pad itself. Unlike the PVC logo, it is also EVA material same as pad, and also shows with the texture. The design of this logo can not be too detailed and small, it needs to be larger and simpler so that we can use the different color EVA material to connect them.
Precautionary installation instructions for swirling vortex flowmeters
There are two ways to make the logo on the traction pad, one is PVC logo, the other one is EVA color connect logo.
PVC logo is a very simple idea, just make a PVC logo based on the design and insert it into the traction pad. One advantage of PVC logo is that it can be more detailed and complicated than the EVA color connect logo. And it can be repeatly used on other pads without any more setup tooling charge.
The precession vortex flowmeter adopts the latest micro-processing technology and has the advantages of strong functions, wide flow range, simple operation and maintenance, and easy installation and use. The precession vortex flowmeter integrates flow, temperature and pressure detection functions and can perform temperature, Automatic pressure compensation, precession vortex flowmeter main technical indicators have reached the advanced level of similar foreign products. Precession vortex flowmeter is widely used in petroleum, chemical, electric power, metallurgy, coal and other industries measuring various gases.
Today we come to understand the working principle of the precession vortex flowmeter. When the fluid passes through the vortex generator composed of spiral blades, the fluid is forced to rotate violently around the generating shaft to form a vortex. When the fluid enters the diffusion section, the vortex flow is subjected to a back flow, and secondary rotation is started to form a gyro-type eddy precession phenomenon. The precession frequency is proportional to the flow rate and is not affected by the physical properties and density of the fluid. The detection element measures the precession frequency of the secondary rotation of the fluid and knows the flow rate. And precession vortex flowmeters can achieve good linearity over a wide range of flow rates.
When the precession vortex flowmeter is installed for the first time, if the pipeline under test does not allow the flow to stop, the installation and sealing of the “mounting base†on the pipeline can be completed before the pipeline has been opened, and then the ball valve is installed. Drill with a continuous drilling rig. After drilling, remove the continuous drilling rig and install the sensor; or remove the continuous rig and temporarily close the ball valve until the sensor is installed. Precession vortex flowmeter power supply is powered by 220V, 24V and lithium battery. The meter can display instantaneous flow and cumulative flow. When the user is used to measure large-diameter pipeline, and when the exact requirements for measurement are different, we can choose this instrument as measurement and measurement. When pre-rotating vortex flowmeter selection, it is necessary to determine whether the medium temperature, pressure, and flow range meet the measurement requirements of the instrument. We must pay attention to the selection of the precession vortex flowmeter and pay attention to the correct installation of the precession vortex flowmeter and the swirl flow to the precession. The plan creates a good operating environment.
When the fluid flowing in the axial direction enters the inlet of the flow sensor, the vane forces the fluid to rotate, and thus generates a vortex flow in the center of the vortex generator. The swirling flow swirls in the venturi tube and reaches the contraction section. The sudden throttle makes the swirl flow Acceleration, when the vortex flow enters the diffusion section, the precession-type secondary rotation is forced by the effect of the backflow.
Precession vortex flowmeters, if not properly installed and maintained, can affect measurement accuracy and other performance. The precession vortex flowmeter should periodically clean the probe of the vortex flowmeter. During the inspection, it was found that the individual probe detection holes have been blocked by dirt and even wrapped in plastic cloth, which will affect the normal measurement. Check the grounding and shielding regularly to eliminate outside interference. Install the probe in a damp environment. It should be dried once a day or treated with moisture. Since the probe itself is not damp-proof at the end, it will affect the operation after getting wet. The management of the data data of the precession vortex flowmeter instrument should be given sufficient attention to facilitate future work. The precession of the vortex flowmeter manufacturers reminds everyone to check regularly to avoid damage.