In the past, the main destinations for China's tire exports were the United States and the European Union. However, the US Department of Commerce recently obtained a partial government subsidy for some Chinese tires. If the arbitration results remain unchanged, the Chinese tire industry will face a punitive tariff of 17.7% to 81.3%. The EU has also graduated from the list of countries enjoying GSP treatment since 2015, and no longer grants preferential treatment for tariff reductions. The outlook for the two traditional tire export markets in the US and the EU is worrisome, and the development needs of emerging markets are particularly urgent.
Externally Heated Desiccant Compressed Air Dryers
For decades, compressed air users have relied on YUKA HL-WR series heated desiccant air dryer to deliver technology that reduces the cost of operation and improves the reliability of air driven processes.
The HL-WR Series is engineered to deliver ISO 8573.1. Air Quality and reduce purge air consumption.
The micro heated regeneration adsorption dryer is a kind of humidification purification device that uses micro heat regeneration method to adsorb and dry compressed air according to the principle of pressure swing adsorption.
Feature & benefit
1. Micro-thermal regeneration adsorption dryer (hereinafter referred to as micro-thermal suction dryer), which has the advantages of both heating regeneration and non-thermal regeneration. The regeneration gas is micro-heated to reduce the regeneration air consumption and the regeneration is more thorough, Extend the tower switching cycle.
Under normal operating conditions, the dew point (under pressure) of the air can be reduced to below -40℃, and the lowest can reach -70℃. It can provide oil-free and water-free high-quality compressed air for a few applications that have high requirements for air quality.
It is especially suitable for use in cold areas in the north and other places where the ambient temperature is below 0°C.
2. The micro heat absorption dryer adopts a double tower structure, one tower absorbs moisture in the air under a certain pressure, and the other tower uses a small portion of dry air slightly higher than atmospheric pressure to regenerate the desiccant in the adsorption tower after a certain period of time , The two towers are switched to ensure continuous supply of dry compressed air.
3. On the basis of having all the advantages of the non-heat regenerative adsorption dryer, it adopts high-quality stainless steel finned U-shaped heating tube, which has uniform heating and high heat transfer coefficient, which can ensure long-term trouble-free operation.
4. Unique computer control system, visually display the running status of the dryer, and has multiple alarms, protection functions and DCS remote control interface to ensure trouble-free use.
5. The actuator adopts pneumatic angle seat valve and pneumatic butterfly valve. The pneumatic control system adopts deep dry air source and then filtered to ensure reliable action and avoid valve leakage.
6. The height and diameter of the adsorption tower are accurately calculated and experimental results, and the important parameters such as flow velocity and heat and mass transfer are indeed mastered, so as to avoid excessive wear of the adsorbent and tunnel effect.
7. Professional program control design, small air pulse and air pressure fluctuation, effectively reduce the outlet air dust and the regeneration air noise.
8. Convenient and practical cycle time mode and energy-saving economic mode. Regenerative air volume and time program can be adjusted to adapt to various actual use conditions and outlet dew point requirements. The support base has a stable and beautiful appearance, and is easy to install, use and maintain.
desiccant for air dryer,desiccant air dryer for compressor,desiccant compressed air dryer,regenerative desiccant air dryer,desiccant air line dryer Hongrijia Depurate Facility Science & Technology Co.,Ltd. , https://www.yukafilter.com
Since February 8, 2015, China's tire exports to Mexico will enjoy zero tariff treatment. Mexico’s recently passed decree adjusted the MFN tariff rates for several customs tariffs, including the new tariff code 4013.90.99 (rubber inner tube for motorcycles) and the tariff code 4011.40.01 (new inflatable rubber inner tube for motorcycles) . The Mexican side believes that there is no production of the above-mentioned products in its country, and its corresponding importing countries often do not sign free trade agreements with them. Therefore, the country decided to reduce the MFN rate of imports of the above two tariff items to 15% from the original 15%.
Here, Jiangsu Nantong Inspection and Quarantine Bureau reminds China's tire foreign trade enterprises to firmly grasp this machine.